As 828 Bike Computer Manual
This is a COMPLETE Workshop Service / Repair Manual for SUZUKI GSX400FWS 1983-1984. This pdf manual is similar to the factory shop manual and works under all PC based Windows operating systems and even Mac. It provides all technical repair information for rebuilding or maintaining your SUZUKI GSX400FWS 1983-1984. No need to buy those costly Factory Shop Manual CD-ROMs. This manual is complete in itself and has all the information which the Shop Manual CD ROMs contains.It Covers-General Information. Related:GSX400F 1981-1983' COVERS THE FOLLOWING MODEL: GSX400FX (1981 Model) GSX400FZ (1982 Model) GSX400FD (1983 Model) Usually these motos changes only few trough the years,17.95 USDThis manual is complete in itself and contains all technical information required to fix or troubleshoot your SUZUKI GSX400FWS 1983-1984. The manual is written in PDF format which is available for instant download.
Monark Ergomedic 828e Manual
The whole manual is printable or you can print any section of it if you want.Download It NOW!Comments.
Production description:ColorBlackBacklightInvalidWirelessValidDimensions46.46.20mmScreen30mmweightNW:90g GW: 100gBattery(1.5V/AG13)PackingBlisterAccessoriesSensor, Magnet, Gauge stand, Cable, StrapsCertificateCE/CCCWarranty2 years guaranteeInstallation of BatteryRemove the battery cover and put a piece of CR2032 battery into the case. Notice:Positive pole of battery(+)should be set upwards. Then cover the the battery case and screw down. Within Sensor it has a battery(23A/12V), when you want to replace it please move away the battery gate with the direction of arrowhead indicates.
And push the battery with the right direction of indication inside the sensor.Installation of Sensor and MagnetInstall the sensor onto the front fork of bicycle, and the Magnet is installed onto the steel wire at the same side wheel. Sensor can be underlaid with back-up plate and use the strap to fasten onto the front fork. It needs to be installed in 60cm distance from the stopwatch. As the picture below, Adjust the comparative location of Sensor and Magnet, The plane must face to the inductor, Keep the space to be 1.5mm. Magnet can not be set to the centre of Sensor face-to-face, it’s better with the head or tail of Sensor. Press the left button to enter into the Clock Mode.Setting the clock (12H/24H)In the Clock mode press“Left button”for 3 seconds it will enter the 12/24 hr time mode setting, go on to press the left button again to exchange 12/24hr.After the comfirmation please press the right button to enter the hours setting, When the hours number is jumpiness, Press the left button to set, but if Press the right button again it is to set the minutes number, when the number is jumpiness, Press the left button to set. In the mode of TM, press the left button for 3 seconds, TM value clear, also DST, MXS, AVS values.Press the left button to enter into“SCAN”(Automatic Scanner)Mode.Automatic cycle funtion(SCAN)“SCAN”( Automatic Scanner)mode:Every 4 seconds the screen shows DST, MXS, AVS, TM value by turns.
Bike Computer Ebay
In this mode, press the left button for 3 seconds, DST, MXS, AVS&TM value will be cleared. Press the right button to stop the Automatic cycle and enter into Time Mode.Energy saving ModeIn 300 seconds if there has no signal inputs into the stopwatch, the screen will turn into OFF state except CLK clock. When there has signal input or press any button it will come back to the condition before it’s turned off, and all the values will be activated.Sampling modePress left even in any modes, it will enter into the samping mode.Screen will show the time of ride(TM), Press the right button to browse the distance of ride which have been sampled(DST), time(TM), Average speed(AVS), Max speed(MXS)and so on the values.